Powersoft Audio – M30D
1 539,00 € sis. alv 24%
Tuotetta ei vielä toistaiseksi toimiteta verkkokaupan kautta. Tuotetta on kumminkin saatavilla. Toimitusaika on noin 2-4 viikkoa.
General | |||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Number of channels | 2 | ||||||||||||||
Output power | Single channel mode | Distributed line* | Bridge mode | ||||||||||||
4 Ω | 8 Ω | 70V | 100V | 8 Ω | |||||||||||
1500 W | 900 W | 1200 W | 1500 W | 3000W | |||||||||||
Max output voltage / current | 135 Vpeak / 65 Apeak | 100 Vpeak | 140 Vpeak | 270 Vpeak | |||||||||||
AC Main Power | |||||||||||||||
Power supply | Universal, regulated switch mode | ||||||||||||||
Nominal power requirement | 100-240 V ±10%, 50-60 Hz | ||||||||||||||
Operating voltage | 90 V – 264 V | ||||||||||||||
Power consuption** | 115 V | 230 V | |||||||||||||
Idle | 37 W | 0.6 A | 37 W | 0.3 A | |||||||||||
1/8 of max output power @ 4 Ω | 530 W | 7 A | 530 W | 3.54 A | |||||||||||
1/4 of max output power @ 4 Ω | 1024 W | 13.04 A | 1024 W | 6.52 A | |||||||||||
Thermal | |||||||||||||||
Operating temperature range | 0° – 45° C – 32° – 113° F | ||||||||||||||
Thermal dissipation** | 115 V | 230 V | |||||||||||||
Idle | 126 BTU/h | 31.8 kcal/h | 126 BTU/h | 31.8 kcal/h | |||||||||||
1/8 of max output power @ 4 Ω | 529 BTU/h | 133.3 kcal/h | 529 BTU/h | 133.3 kcal/h | |||||||||||
1/4 of max output power @ 4 Ω | 935 BTU/h | 235.6 kcal/h | 935 BTU/h | 235.6 kcal/h | |||||||||||
AUDIO | |||||||||||||||
|
|||||||||||||||
Frequency response | 20 Hz – 20 kHz (±0.5 dB) @ 1 W, 8 Ω | ||||||||||||||
S/N ratio | > 112 dB (20 Hz – 20 kHz, A weighted) | ||||||||||||||
Crosstalk separation | > 70 dB @ 1kHz | ||||||||||||||
THD+N | 0.08% @ 1/2 full power | ||||||||||||||
IMD | 0.02% | ||||||||||||||
Input impedance | 10 kΩ balanced | ||||||||||||||
Slew rate | 40 V/μs @ 8Ω, input filter bypassed | ||||||||||||||
Damping factor | > 5000 @ 100 Hz | ||||||||||||||
DSP | |||||||||||||||
DSP architecture | Analog Devices ADAU® 1701 DSP | ||||||||||||||
AD Converter | Cirrus Logic CS 5381, 2 channel, 24 bit @ 48 kHz, 120 dB S/N | ||||||||||||||
DA Converter | Cirrus Logic CS 4398, 2 channel, 24 bit @ 48 kHz, 120 dB S/N | ||||||||||||||
Internal precision | Fixed point | ||||||||||||||
Firmware | Network upgradable firmware | ||||||||||||||
Latency | 0.644 ms fixed latency architecture | ||||||||||||||
Input equalizer | up to 5 biquad IIR filters (PEQ, shelving, band pass, band stop, all pass) | ||||||||||||||
Output equalizer | 16 fully parametric filters per channel, IIR: peaking, hi/lo-shelving, hi/lo-pass, band-pass, band-stop, all-pass. Custom FIR up to 384 taps @ 48 or 96 kHz | ||||||||||||||
Crossover | Butterworth, Linkwitz-Riley, Bessel: 6 dB/oct to 48 dB/oct | ||||||||||||||
Delay | 340 ms input delay plus 10 ms per output | ||||||||||||||
Limiters | Peak limiter, RMS limiter, frequency dependent RMS limiter | ||||||||||||||
Damping control | < 120 Hz, range ±2 Ω | ||||||||||||||
Front panel | |||||||||||||||
Indicators and Controllers | 1 x LED – Status 1 x LED – Over-temperature protection 2 x LED bar – Signal level + CLIP 2 x Knob – Level attenuator (stepped) 1 x Power switch – |
||||||||||||||
Connectors | |||||||||||||||
AC main | 1 x IEC C14 connector – 15 A max (region-specific power cord provided) | ||||||||||||||
Audio signal input | 2 x XLR – Signal input | ||||||||||||||
Auxiliary voltage | 1 x 2 pin Phoenix MC 1.5/2-ST-3.81 – External voltage connector (DSP version only) | ||||||||||||||
Audio out (link through) | 2 x XLR – Signal output (link through) | ||||||||||||||
Loudspeakers | 2 x speakON – Neutrik NL4MD | ||||||||||||||
Network/data | 1 x Rj45 socket – RS485 data connection (non-DSP version) | ||||||||||||||
Construction | |||||||||||||||
Dimensions (L x H x W) | 483 mm x 44.45 mm x 358 mm (19.0 in x 1.8 in x 14.1 in) | ||||||||||||||
Weight | 7.4 kg (16.3 lb) |
Varasto loppu
Kuvaus
OVERVIEW CHART
Like all M Series models, the M30D is optimized for 4Ω, and with its output power ideal for small to medium sized sound systems where e.g. no more than two 8Ω loads are connected in parallel to an amplifier channel: Why overpaying for amplifiers capable of driving 2Ω loads?
Alternatively, the M30D can drive constant voltage lines directly where multiple loudspeakers are required, but only few different signals.
Maximum efficiency warrants minimum current draw, heat dissipation and power consumption, resulting in “green” products, saving the user a substantial amount of money over time.
The M30D HDSP+ETH version provides on-board DSP and Ethernet interfaces.
The high-performance DSP is hidden inside and safe against accidental or intentional tampering; monitoring and amplifier settings can be done via Armonía Pro Audio Suite™(Interface available for MediaMatrix, Crestron, AMX, Q-SYS control and monitoring systems).
Locally, the M30D HDSP+ETH lets the user access up to four presets per pushbutton on the rear panel.
Vain kirjautuneet asiakkaat -jotka ovat ostaneet tuotteen- voivat kirjoittaa tuotearvion.
Arviot
Tuotearvioita ei vielä ole.